For those who have read my last teardown of the, they would have noted my discovery that it was not compatible with decoding through rtl-sdr due to a. I haven’t had any time or inclination to better understand the HM01 format, although it superficially does look simpler. Instead, I had another different unit on the way. I was using an Efergy Elite 1.0 at home at the time, and as that unit is discontinued, my only option was to order its successor, the Elite Classic 2.0. This unit itself may have already been superseded at the time that I publish this post, as mentions of the Elite Classic 3.0 have already started popping up on the internet. ![]() Below are a series of basic troubleshooting instructions for the Travel Scooter. This information is to be used as a supplement to the troubleshooting instructions provided in the owner’s manual. If you have any questions about this information, contact your authorized Pride Provider. What if my Travel Scooter will not power up? The elite wireless electricity monitor shows the amount of energy that a household is. Cable which connects the meter to the consumer unit. Giovanni allevi panic pdf to word converter. Any power you use in your home will pass through this cable. -1 x Instruction manual for the monitor Transmitter Monitor Sensor. The unit arrived not long after my HM01, although, as I was tied up with other work, I forgot all about it until I “rediscovered” it under a pile of stuff. So here’s quick review and teardown. The Bundle The Efergy Elite Classic 2.0 comes in a cardboard box which illustrates the receiver LCD and its options. Quite simple and yet, also a good preview of what the unit is capable of. The unit itself is about $80 posted to Australia from the UK (via eBay). The rear of the box gives you an illustration of how to install and run the unit – it’s almost enough to use it without the need for reading the manual. A short manual is included, along with the listed items. You will need six AA batteries, three in the transmitter, and three in receiver. The rear illustration already shows some differences to the Elite 1.0, such as the increased decimal digit accuracy, and the inclusion of temperature and humidity sensors. I should make a note now, the receivers and transmitters for the Elite 1.0 and 2.0 aren’t interchangeable in the sense the Elite 1.0 R (LCD) doesn’t detect the Elite 2.0 transmitter and vice versa. Despite this, EfergyRPI_001 manages to decode the transmissions from the Elite 1.0, Elite Classic 2.0 and E2 successfully. Those are the only ones I know to work with similar transmission formats. So that’s a BIG bonus! You will note that the revision of the product isn’t noted on the front or back of the box, and can only be seen from the underside. This one also seems to list its firmware revision as being 2.0. Here are the items included in the kit. Epica unleashed download mp3. There is a short manual, the LCD receiver itself with a protective film, the transmitter (with two ports covered by removable rubber caps, to be used with additional current transformers if on a three phase installation), and the current transformer which attaches with a 2.5mm TRS jack. I did give it a short spin – and all I can say is that it has the same allure as the original Elite 1.0, and works pretty much equally well. The bolder font on the buttons and the new logo colouration is probably good as well. The build quality is miles ahead of the HM01 – and the price difference is small. I would advise anyone looking to buy the HM01 to buy this instead. Tearing it Apart Here comes the fun bit – looking at each of the bits and pulling it apart. One thing that has changed is the printing on the products, which allude to large numbers of certifications – this wasn’t present on the Elite 1.0, and gives us a chance to chase down who is responsible for the unit altogether. Feel free to compare how the insides of this energy monitor compares to the. The receiver unit claims to be designed in the UK and Made in China, just like the Elite 1.0. The receiver unit is so well built, and no screws are obviously evident that I took a while to work it out – the grey soft-touch sides come off to reveal the screws. One thing that’s different is that the input is now specified as DC 5v, whereas the Elite 1.0 specified DC 6v.
0 Comments
Leave a Reply. |